The P0060 trouble code is a generic OBD-II powertrain code indicating a detected fault in the heated oxygen sensor (HO2S) heater circuit resistance for Bank 2, Sensor 2.
Because it is a generic code, the definition applies across all manufacturers, though specific diagnostic procedures and wiring diagrams vary by vehicle. Testing is required to identify the root cause.
Quick Navigation
Key Takeaways
- P0060 is a generic code indicating the powertrain control module detected abnormal resistance in the Bank 2 Sensor 2 oxygen sensor heater circuit.
- Possible causes include a failed oxygen sensor heater element, damaged wiring, poor connector contact, or a blown heater circuit fuse.
- Symptoms typically include an illuminated Check Engine Light and potentially delayed closed-loop fuel control or failed emissions tests.
- Proper diagnosis requires verifying the heater circuit resistance and inspecting the wiring harness before replacing components.
- Repairs range from repairing damaged wiring to replacing the downstream oxygen sensor on Bank 2.
P0060 Code Description and Implications
The P0060 code is a generic powertrain definition. It indicates that the powertrain control module (PCM) has detected an abnormal electrical resistance in the heater circuit of the downstream heated oxygen sensor on Bank 2, Sensor 2.
The oxygen sensor heater brings the sensor to operating temperature quickly, allowing the engine to enter closed-loop fuel control and monitor catalytic converter efficiency sooner. When the resistance falls outside the expected range, the PCM sets this trouble code and illuminates the Check Engine Light.
Common Causes of the P0060 Code
Electrical faults and component degradation are the primary triggers for this circuit malfunction. The PCM monitors the heater circuit for resistance values that are too high or too low.
Failed heater element: The internal heating element inside the Bank 2 Sensor 2 oxygen sensor can degrade, burn out, or develop an internal short over time.
Wiring or connector damage: The wiring harness routing to the downstream sensor is exposed to extreme heat, road debris, and moisture, which can lead to chafed insulation, broken wires, or corroded connector pins.
Blown fuse or power supply issue: A shared heater circuit fuse may blow due to a short to ground, or a poor ground connection can prevent the heater from receiving adequate voltage.
Symptoms Associated With P0060
When the PCM detects an oxygen sensor heater circuit fault, it illuminates the Check Engine Light.
Delayed closed-loop operation: Without a functioning heater, the downstream sensor takes longer to reach operating temperature, which may delay closed-loop fuel control and cause the vehicle to fail an emissions inspection.
Drivability issues: In most applications, a heater circuit fault alone does not cause severe drivability symptoms like rough idling or stalling, as the sensor eventually reaches operating temperature from exhaust heat.
Diagnosing the P0060 Trouble Code
Accurate diagnosis begins by confirming the exact factory wiring diagram for your specific vehicle make and model.
Visual inspection: Inspect the Bank 2 Sensor 2 wiring harness and connectors. Look for chafed insulation against the exhaust, melted connectors, or corrosion inside the plug.
Circuit testing: Using a digital multimeter, measure the resistance across the heater circuit pins on the oxygen sensor connector. Compare the reading to the manufacturer specification to verify if the internal heater element is open, shorted, or within range.
Repairing the P0060 Issue
Repairs must address the specific root cause identified during testing.
Wiring repair: If a broken wire, short to ground, or corroded connector is found, repair the harness using solder and heat-shrink tubing or replace the connector pigtail.
Component replacement: If the wiring and power supply are intact but the sensor heater element fails resistance testing, replace the Bank 2 Sensor 2 oxygen sensor with a component meeting the correct vehicle specification.
Cost Considerations for P0060 Repairs
Cost depends on diagnostic time, component accessibility, required parts, programming requirements, and labor.
Replacing a downstream oxygen sensor is generally a straightforward repair with moderate parts and labor costs, provided the sensor is accessible and not seized in the exhaust pipe.
Prevention Strategies for Future Occurrences
While internal heater element failures cannot always be predicted due to normal aging, you can protect external circuits from common damage.
Inspecting the oxygen sensor wiring harness for early signs of melting or rubbing against the exhaust system can help prevent short circuits from developing.
Troubleshooting Tips and Best Practices
Do not assume the powertrain control module requires replacement just because a P0060 code is present. A pinched wire or blown fuse will produce the exact same resistance fault reading.
Always check the oxygen sensor heater fuse first. If the fuse is blown, do not simply replace it, as a shorted heater element or chafed wire will blow the new fuse immediately.
Check for Technical Service Bulletins for your specific vehicle. Manufacturers occasionally release updated sensor part numbers or revised wiring harnesses to address chronic heater circuit faults.
More OBD-II Codes
| P0050 | P0031 | P0030 | P0016 |
| P0014 | P0013 | P0100 | P0121 |
| P0135 | P0141 | P0155 | P0161 |
| P0130 | P0136 | P0150 | P0156 |
| P0171 | P0174 | P0201 | P0300 |
| P0420 | P0440 | P0455 | P0012 |
Frequently Asked Questions
Is P0060 a generic or manufacturer-specific code?
No. P0060 is a generic OBD-II powertrain code. Its definition as a Bank 2 Sensor 2 oxygen sensor heater circuit fault applies universally across all vehicle makes.
Can I drive my car with a P0060 code?
Driving is generally possible, as the engine will still run. However, the vehicle may fail an emissions test, and prolonged driving with a heater fault can delay closed-loop fuel control.
Will disconnecting the battery clear the P0060 code?
Disconnecting the battery may temporarily erase the code, but it will not repair a blown fuse, damaged wiring, or a failed internal heater element. The code will return once the monitor runs.
Can a bad catalytic converter cause a P0060 code?
No. P0060 specifically monitors the electrical resistance of the oxygen sensor’s internal heater circuit. A catalytic converter efficiency issue triggers different codes, such as P0420 or P0430.
Does P0060 always mean the oxygen sensor is bad?
No. The code identifies a detected circuit resistance condition. This is frequently caused by a blown fuse, damaged wiring, or a poor connector. The sensor should only be replaced after testing confirms failure.
What Should You Do About the P0060 Code?
Confirm the exact factory wiring diagram for your vehicle, then follow the applicable manufacturer diagnostic procedure. Because P0060 is a generic code, the diagnostic path for the heater circuit is standardized, but the exact pinout and fuse locations vary by application.
Inspect the relevant system and components, including the Bank 2 Sensor 2 wiring harness, heater fuses, and connectors. Repair any confirmed wiring faults, or replace the relevant system components only after testing verifies the failure.
